LMTLF9UA102W0R8 [TAIYO YUDEN]
Single Phase EMI Filter, 250V, 50HzHz, ROHS COMPLIANT PACKAGE-4;
| 型号： | LMTLF9UA102W0R8 |
| 厂家： | 
TAIYO YUDEN (U.S.A.), INC |
| 描述： | Single Phase EMI Filter, 250V, 50HzHz, ROHS COMPLIANT PACKAGE-4 LTE |
| 文件： | 总32页 (文件大小：1239K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Notice for TAIYO YUDEN productsꢀ
Please read this notice before using the TAIYO YUDEN products.
REMINDERS
■ Product information in this catalog is as of October 2009. All of the contents specified herein are subject to change
without notice due to technical improvements, etc. Therefore, please check for the latest information carefully be-
fore practical application or usage of the Products.
Please note that Taiyo Yuden Co., Ltd. shall not be responsible for any defects in products or equipment incorpo-
rating such products, which are caused under the conditions other than those specified in this catalog or individual
specification.
■ Please contact Taiyo Yuden Co., Ltd. for further details of product specifications as the individual specification is
available.
■ Please conduct validation and verification of products in actual condition of mounting and operating environment
before commercial shipment of the equipment.
■ All electronic components or functional modules listed in this catalog are developed, designed and intended for
use in general electronics equipment.(for AV, office automation, household, office supply, information service,
telecommunications, (such as mobile phone or PC) etc.). Before incorporating the components or devices into any
equipment in the field such as transportation,( automotive control, train control, ship control), transportation signal,
disaster prevention, medical, public information network (telephone exchange, base station) etc. which may have
direct influence to harm or injure a human body, please contact Taiyo Yuden Co., Ltd. for more detail in advance.
Do not incorporate the products into any equipment in fields such as aerospace, aviation, nuclear control, subma-
rine system, military, etc. where higher safety and reliability are especially required.
In addition, even electronic components or functional modules that are used for the general electronic equipment,
if the equipment or the electric circuit require high safety or reliability function or performances, a sufficient reliabil-
ity evaluation check for safety shall be performed before commercial shipment and moreover, due consideration to
install a protective circuit is strongly recommended at customer's design stage.
■ The contents of this catalog are applicable to the products which are purchased from our sales offices or distribu-
tors (so called“TAIYO YUDEN’s official sales channel”).
It is only applicable to the products purchased from any of TAIYO YUDEN’s official sales channel.
■ Please note that Taiyo Yuden Co., Ltd. shall have no responsibility for any controversies or disputes that may oc-
cur in connection with a third party's intellectual property rights and other related rights arising from your usage of
products in this catalog. Taiyo Yuden Co., Ltd. grants no license for such rights.
■ Caution for export
Certain items in this catalog may require specific procedures for export according to“Foreign Exchange and For-
eign Trade Control Law”of Japan,“U.S. Export Administration Regulations”, and other applicable regulations.
Should you have any question or inquiry on this matter, please contact our sales staff.
Should you have any question or inquiry on this matter, please contact our sales staff.
notice_e-01
WOUND TORROIDS AND BEADS
WAVE
■ FEATURES
■ APPLICATIONS
◦Use of high loss ferrite materials for excellent high frequency noise
absorption.
◦Absorption of high frequency noise from digital equipment data lines.
■ OPERATING TEMP.
◦High impedance for normal mode applications.
◦05 RD type available in taping for automatic insertion.
◦06 BT type is designed for high current applications (3A).
◦ー25℃～105℃（Including self-generated heat）
■ ORDERING CODE
【FL-R / RD Type】
F L 0 5 R D 2 0 0 A T ○
❶
❷
❸
❹
❺
❻
❼
❶Type
Wound torroids
and beads
❸Shape
❹Nominal inductance
(μH)
example
❺Inductance tolerance
Higher than normal value
❻Packaging
Bulk
❼Internal code
Standard product
Ring core,
A
E
△
T
△
FL
R△
with single wire lead
Special tolerance
Tape & Reel
Ammo
Product classification
code
07
Ring core,
with case, pin type
1R0
200
1.0
20.0
Z
RD
❷Dimensions of core
05
△＝Blank space
ー
Special code
△＝Blank space
4.8mm
△＝Blank space
※R＝decimal point
【FL-BT Type】
F L 0 6 B T 0 4 ○
❶
❷
❸
❹
❺
❶Type
FL Wound torroids and beads
❷Dimensions of core
❸Shape
Cylinder,
porous core
❹Product classification code
❺Internal code
Standard product
△＝Blank space
(diameter)
04
△
BT
06
6.0mm
■ EXTERNAL DIMENSIONS/MINIMUM QUANTITY
Type
〔05RD〕
〔05R〕
〔06BT04〕
9.0max
3.7max
（0.35max）
（0.146max）
6.5max
（0.256max）（0.118max）
3.0max
15.2max
（0.598max）
Fig.
φ0.6
（φ0.024）
φ6.0±0.2
（φ0.24±0.008）
φ0.3
（φ0.012）
＋0.6
ー0.2
5.0
＋0.024
ー0.008
（0.197
）
Bulk
400
2000
1500
500
ー
ー
250
Minimum
Quantity
(pcs.)
Tape & Reel
Ammo
ー
ー
Unit : mm (inch)
■ IMPEDANCE-FREQUENCY CHARACTERISTICS
Measured by HP4291A
FL05RD / FL05R TYPE
FL06BT TYPE
Please contact TAIYO YUDEN for further information in regard to other characteristics.
＊This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
filter01_e-01
120
■ PART NUMBERS
EHS (Environmental
Hazardous
Inductance
[μH]
Impedance
〔Ω〕(typical)
DC Resistance
〔Ω〕(max)
Rated current
〔A〕(max)
Ordering code
Substances
)
＋1.0
FL05RD 1R0E□
FL05R 100A
RoHS
1.0
800 (at 400MHz)
900 (at 200MHz)
0.08
0.05
0.5
1.5
3.0
－0.5
RoHS
10 min.
FL05RD 100A□
FL05R 200A－07
FL05RD 200A□
FL06BT 04
RoHS
RoHS
20 min.
2000 (at 100MHz)
1000 (at 150MHz)
0.08
0.05
RoHS
RoHS
ー
□Please specify the packaging code (T: Tape & reel, Z : ammo, Blank space : bulk)
＊This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
filter01_e-01
121
■ PACKAGING
①Minimum Quantity
Type
Minimum Quantity (pcs.)
Bulk
500
400
250
Tape & Reel
Ammo
ー
1500
FL05R
ー
2000
ー
FL05RD
FL06BT
ー
②Taping dimensions
◦FL05RD
Type
Symbol
Dimension
D1
H2
T
9.0 max. (0.354 max.)
9.0 max. (0.354 max.)
3.7 max. (0.146 max.)
H1
H
31.0 max. (1.22 max.)
18.0±1.0 (0.709±0.039)
12.7±1.0 (0.500±0.039)
12.7±0.3 (0.500±0.012) ※1
3.85±0.8 (0.152±0.031)
6.35±1.3 (0.250±0.051)
P
P0
P1
P2
W1
＋0.75
＋0.030
)
ー0.020
9.0
(0.354
ー0.5
FL05RD
＋0.6
＋0.024
)
ー0.008
F
d
5.0
(0.197
ー0.2
φ0.6 (φ0.024)
△h
W
W0
W2
ℓ
D0
L
0±2.0 (0±0.079)
＋1.0
ー0.5
＋0.024
18.0
(0.709
)
ー0.008
12.5 min. (0.492 min.)
3.0 min. (0.118 min.) ※2
0 max. (0 max.)
4.0±0.3 (0.157±0.012)
11.0 max. (0.433 max.)
0.7±0.2 (0.028±0.008)
t
※1 Accumulated error for 20 pitches shall be within ±2mm.
※2 Pasting tape shall not exceed paste board.
Unit : mm (inch)
③Reel size
◦FL05RD
60 or les〔s 53〕
（2.362 or les〔s 2.087〕
Unit : mm (inch)
）
Dimensions in parenthesis are measured value.
＊This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
filter01_pack_e-01
filter01_pack-P1
■ RELIABILITY DATA
1. Operating temperature Range
LA Type
CAL45 Type
ー25～＋105℃
LHL□□□
FBA/FBR
ー25～＋85℃
ー25～＋105℃
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA・CA・FL : Including self-generated heat
LHL□□□ : Including self-generated heat
2. Storage temperature Range
LA Type
CAL45 Type
LHL□□□
FBA/FBR
ー40～＋85℃
FL05□ Type
FL06BT Type
3. Rated current
LA Type
CAL45 Type
LHL□□□
FBA/FBR
Within the specified tolerance
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA
: The maximum DC value having inductance within 10% and temperature incease within 40℃ (LA:20℃) by the application of DC bias.
LHL□□□ : The maximum DC value having inductance decrease within 10% (LHLC08, LHLC10：within 30%) and temperature increase within the following specified
temperature by the application of DC bias.
Reference temperature : 25℃ (LHL08, LHL10, LHL13)
: 30℃ (LHL16, LHLP□□)
: 40℃ (LHLC08, LHLC10)
FB
FL
: No disconnection or appearance abnormality by continuous current application for 30 min. Change after the application shall be within ±20% of the initial value.
This is not guaranteed for electrial characteristics during current application.
: The maximum DC value having temperature rise within specified value.
4. Impedance
LA Type
CAL45 Type
LHL□□□
FBA/FBR
Within the specified tolerance
Refer to individual specification
FL05□ Type
FL06BT Type
【Test Method and Remarks】
FB
: Measuring equipment : Impedance analyzer (HP4191A) or its equivalent
Measuring frequency : Specified frequency
FL06BT : Measuring equipment : 4291A (HP) or its equivalent
Measuring frequency : Specified frequency
5. Inductance
LA Type
CAL45 Type
Within the specified tolerance
LHL□□□
FBA/FBR
FL05□ Type
Within the specified tolerance
FL06BT Type
【Test Method and Remarks】
LA, CA
: Measuring equipment : LCR meter (HP4285A + HP42851A or its equivalent)
Measuring frequency : Specified frequency
LHL□□□ : Measuring equipment : LCR meter (HP4285A＋HP42851A or its equivalent)
LCR meter (HP4263A) or its equivalent (at 1KHz)
Measuring frequency : Specified frequency
FL05R□ : Measuring equipment : HP4262A or its equivalent
Measuring frequency : 1kHz
6. Q
LA Type
Within the specified tolerance
CAL45 Type
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA : Measuring equipment : LCR meter (HP4285A + HP42851A or its equivalent)
Measuring frequency : Specified frequency
LHL□□□ (except LHLP) : Measuring equipment : LCR meter (HP4285A＋HP42851A or its equivalent)
LCR meter (HP4263A) or its equivalent (at 1kHz)
Measuring frequency : Specified frequency
＊This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
le0104fi01_reli_e-01
le0104fi01_reli-RP1
■ RELIABILITY DATA
7. DC Resisitance
LA Type
CAL45 Type
LHL□□□
FBA/FBR
Within the specified tolerance
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA : Measuring equipment : low ohmmeter (A&D AD5812 or its equivalent)
LHL□□□・FB・FL : Measuring equipment : DC ohmmeter
8. Self resonance frequency
LA Type
Within the specified tolerance
CAL45 Type
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA : Measuring equipment : Network analyzer (Anritsu MS620J or its equivalent)
LHL□□□ (except LHLP) : Measuring equipment : (HP4191A, 4192A) its equivalent
9. Temperature characteristic
LA Type
△L/L : Within ±5%
CAL45 Type
LHL□□□
△L/L : Within ±7% (except LHLP16 : Within ±20%)
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA : Change of maximum inductance deviation in step 1 to 5
Step
Temperature (℃)
1
2
3
4
5
20
ー25 (Minimum operating temperature)
20 (Standard temperature)
＋85 (Maximum operating temperature)
20
LHL□□□ : Change of maximum inductance deviation in step 1 to 5
Temperature at step 1 : 20℃
Temperature at step 2 : Minimum operating temperature
Temperature at step 3 : 20℃ (Standard temperature)
Temperature at step 4 : Maximum operating temperature
Temperature at step 5 : 20℃
10. Terminal strength : tensile force
LA Type
CAL45 Type
No abnormality such as cut lead, or looseness.
LHL□□□
FBA/FBR
No abnormality such as cut lead, or looseness.
No abnormality such as cut lead, or looseness.
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA
: Apply the stated tensile force progressively in the direction to draw terminal.
force (N)
25
duration (s)
5
CA
: Apply the stated tensile force progressively in the direction to draw terminal.
force (N)
10
duration (s)
10
LHL□□□ : Apply the stated tensile force progressively in the direction to draw terminal.
Nominal wire diameter tensile φd (mm)
force (N)
duration (s)
0.3＜φd≦0.5
5
0.5＜φd≦0.8
0.8＜φd≦1.2
10
25
30±5
FBA/FBR : A bead shall be fixed and static loaded 20±1N (2.0±0.1 kgf) in axial direction of lead wire in 10±1 seconds.
FL05R□ : Fix the component in the direction to draw terminal,and gradually apply the tensile force of 4.9N.
11. Over current
LA Type
No emission of smoke no firing.
CAL45 Type
There shall be no scorch or short of wire.
LHL□□□
LHLC08,LHLC10 : There shall be no firing.
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LHL□□□/LA・CAL45 Type：Measuring current
Duration
: Rated current×2
: 5 min.
Number of measuring
: one time
＊This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
le0104fi01_reli_e-01
le0104fi01_reli-RP2
■ RELIABILITY DATA
12. Terminal strength : bending
LA Type
CAL45 Type
No abnormality such as cut lead, or looseness.
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA : Suspend a mass at the end the terminal, incline the body though angel of 90 and return it to initial position. This operation is done over a period of 2-3 sec. Then sec-
ond bend in the opposite direction shall be made.
Number of bends : Two times.
Nominal wire diameter tensile
Bending force
(N)
Mass reference weight
(kg)
φd (mm)
0.5＜φd≦0.8
5
0.50
LH・FB : Suspend a mass at the end the terminal, incline the body though angel of 90 and return it to initial position. This operation is done over a period of 2-3 sec. Then sec-
ond bend in the opposite direction shall be made.
Number of bends : Two times.
Nominal wire diameter tensile
Bending force
(N)
Mass reference weight
(kg)
φd (mm)
0.3＜φd≦0.5
0.5＜φd≦0.8
0.8＜φd≦1.2
2.5
5
0.25
0.5
10
1.0
13. Insulation resisitance : between the terminals and body
LA Type
CAL45 Type
LHL□□□
FBA/FBR
100MΩ min.
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LHL□□□ : Applied voltage : 500 VDC
Duration
: 60 sec.
14. Insulation resistance : between terminals and core
LA Type
CAL45 Type
LHL□□□
FBA/FBR
1MΩ min. (Other than materail code MA)
FL05□ Type
FL06BT Type
【Test Method and Remarks】
FBA・FBR : Applied voltage : 100 VDC
Duration
: 60±5 sec.
15. Withstanding : between the terminals and body
LA Type
CAL45 Type
LHL□□□
FBA/FBR
No abnormality such as insulation damage
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LHL□□□ : Accoding to JIS C5102. 7. 1. 3 (C)
Metal global method
Applied voltage : 500 VDC
Duration
: 60 sec.
16. DC bias characteristic
LA Type
△L/L : Within ー10%
CAL45 Type
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA : Measure inductance with appliation of rated current using LCR meter to compare it with the initial value.
17. Body strength
LA Type
No abnormality as damage.
CAL45 Type
LHL□□□
FBA/FBR
No abnormality such as cracks on body.
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA
: Applied force : 30N
Duration
Speed
: 10 sec.
: Shall attain to specified force in 2 sec.
CAL45 : Applied force : 50N
Duration
Speed
: 10 sec.
: Shall attain to specified force in 2 sec.
FBA
: Applied force : 50±3N
Duration : 30±1 sec.
＊This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
le0104fi01_reli_e-01
le0104fi01_reli-RP3
■ RELIABILITY DATA
18. Resisitance to vibration
LA Type
△L/L : Within ±5%ꢀQ : 30min
△L/L : Within ±5%
CAL45 Type
LHL□□□
Appearance : No abnomality
△L/L : Within ±5%
Q change : Within ±30% (LHLP : only △L/L)
FBA/FBR
Appearance : No abnomality
Impedance change : Within ±20%
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA
: Directions
: 2 hrs each in X, Y and Z directions total : 6hrs.
Frequency range : 10 to 55 to 10Hz (1min.)
Amplitude : 1.5mm
Mounting method : Soldering onto printed board.
Recovery : At least 1hr of recovery under the standard condition after the test, followed by the measurement within 2hrs.
LHL□□□・FB：Directions
: 2 hrs each in X, Y and Z directions total : 6hrs.
Frequency range : 10 to 55 to 10Hz (1min.)
Amplitude
: 1.5mm (But don't exceed acceleration 196m/s2 (two power))
Mounting method : Soldering onto printed board.
19. Resistance to shock
LA Type
No significant abnormality in appearance
CAL45 Type
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA
:
Drop test
Impact material : concrete or vinyl tile
Height : 1m
Total number of drops : 10 times
20. Solderability
LA Type
At least 75％ of terminal electrode is covered by new solder.
CAL45 Type
LHL□□□
FBA/FBR
At least 75％ of terminal electrode is covered by new solder.
At least 90％ of terminal electrode is covered by new solder.
FL05□ Type
FL06BT Type
At least 75％ of terminal electrode is covered by new solder.
【Test Method and Remarks】
LA, CA
: Solder temperature : 230±5℃
Duration : 2±0.5 sec.
LHL□□□ : Solder temperature : 235±5℃
Duration
Immersion depth
: 2±0.5 sec.
: Up to 1.5mm from bottom of case.
FB
: Solder temperature : 230±5℃
Duration
: 3±1 sec.
Immersion depth
: Up to 1.5mm from terminal root.
FL05R□ : Solder temperature : 230±5℃
Duration
Immersion depth
: 2±0.5 sec.
: Up to 2 to 2.5mm from terminal root.
FL06BT
: Solder temperature : 230±5℃
Duration
: 3±1 sec.
Immersion depth
: Up to 0.5 to 1.0mm from terminal root.
21. Resisitance to soldering heat
LA Type
No significant abnormality in appearance
△L/L : Within ±5%
CAL45 Type
LHL□□□
FBA/FBR
No significant abnormality in appearance
No significant abnormality in appearance
Refer to individual specification
Inductance change : Within ±5%
Impedance change : Within ±20%
Q change : Within ±30%(LHLP : only △L/L)
FL05□ Type
FL06BT Type
No significant abnormality in appearance
Impedance change : Within ±20%
【Test Method and Remarks】
LA, CA
: Solder temperature : (CA) 270±5℃, (LA) 260±5℃
Duration
: 5±0.5 sec. One time
Immersed conditions : Inserted into substrate with t=1.6mm
Recovery
: At least 1hr of recovery under the standard condition after the test, followed by the measurement within 2hrs.
LHL□□□ : Solder bath method : Solder temperature : 260±5℃
Duration
: 10±1 sec.
Up to 1.5mm from bottom of case.
Manual soldering
: Solder temperature : 350±10℃ (At the tip of soldering iron)
Duration
: 5±1 sec.
Up to 1.5mm from bottom of case.
Caution
: No excessive pressing shall be applied to terminald.
Recovery
: 4 to 24hrs of recovery under the standard condition after the test.
FB
FL
: Solder bath method : Condition 1 : Solder temperature : 260±5℃
Duration
: 10±1 sec.
Immersion depth
: Up to 1.5mm from terminal root.
Condition 2 : Solder temperature : 350±5℃
Duration
Immersion depth
: 3±1 sec.
: Up to 1.5mm from terminal root.
Recovery
: 3hrs of recovery under the standard condition after the test.
: Solder condition
Immersion depth
Recovery
: 260±5℃
10±1 sec.
: Up to 0.5 to 1.0mm from terminal root.
: 3hrs of recovery under the standard condition after the test.
＊This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
le0104fi01_reli_e-01
le0104fi01_reli-RP4
■ RELIABILITY DATA
22. Resisitance to solvent
LA Type
Please avoid the ultrasonic cleaning of this product.
No significant abnormality in appearance
CAL45 Type
LHL□□□
FBA/FBR
Impedance change : Within ±20%
FL05□ Type
FL06BT Type
【Test Method and Remarks】
FB : Solvent temperature : 20～25℃
Duration
Solvent type
Recovery
: 30±5 sec.
: Acetone, trichloroethylene
: 3hrs of recovery under the standard condition after the test.
23. Thermal shock
LA Type
△L/L : Within ±10%ꢀQ : 30min
△L/L : Within ±10%
CAL45 Type
LHL□□□
FBA/FBR
Appearance : No abnormality
Appearance : No abnormality
Refer to individual specification
Appearance : No abnormality
Inductance change : Within ±10%
Impedance change : Within ±20%
Q change : Within ±30% (LHLP：only △L/L)
FL05□ Type
FL06BT Type
Impedance change : Within ±20%
【Test Method and Remarks】
LA, CA
: Conditions for 1cycle
Step
Temperature (℃)
Duration (min.)
30±3
Within 3
30±3
＋0
ー3
1
2
3
4
ー25
Room temperature
＋2
＋85
ー0
Room temperature
Within 3
Number of cycles : 5 cycles
Recovery : At least 1hr of recovery under the standard condition after the removal from test chamber, followed by the measurement within 2hrs.
LHL□□□・FB : Accoding to JIS C0025
Conditions for 1 cycle
Step
Temperature (℃)
Minimum operating temperature
Room temperature
Duration (min.)
30±3
Within 3
30±3
＋0
ー3
1
2
3
4
＋2
ー0
Minimum operating temperature
Room temperature
Within 3
Number of cycles : 10 cycles〔LHL□□□〕
: 5 cycles (FBA, FBR)
Recovery
: 4 to 24hrs of recovery under the standard condition after the removal from the test chamber.〔LHL□□□〕
: 3hrs of recovery under the standard condition after the removal from the test chamber. (FBA, FBR)
FL
: Accoding to JIS C0025
Conditions for 1 cycle
Step
Temperature (℃)
Duration (min.)
30±3
Within 3
30±3
＋0
ー3
1
2
3
4
ー25
Room temperature
＋2
＋85
ー0
Room temperature
Within 3
Number of cycles : 10 cycles
Recovery
: 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
24. Damp heat
LA Type
△L/L : Within ±10%ꢀQ : 30min
△L/L : Within ±10%
CAL45 Type
LHL□□□
FBA/FBR
Appearance：No abnormality
Impedance change：Within ±20%
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA : Temperature : 40±2℃
Humidity
Duration
Recovery
: 90～95%RH
: 1000 hrs
: At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
FB : Temperature : 60±2℃
Humidity
Duration
Recovery
: 90～95%RH
: 1000 hrs
: 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
＊This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
le0104fi01_reli_e-01
le0104fi01_reli-RP5
■ RELIABILITY DATA
25. Loading under damp heat
LA Type
△L/L : Within ±10%ꢀQ : ±30min
△L/L : Within ±10%
CAL45 Type
LHL□□□
FBA/FBR
Appearance : No abnormality
Imductance change : Within ±10%
Impedance change : Within ±20%
Q change : Within ±30% (LHLP : only △L/L)
FL05□ Type
FL06BT Type
Refer to individual specification
Appearance : No abnormality
【Test Method and Remarks】
LA, CA
: Temperature
Humidity
: 40±2℃
: 90～95%RH
Duration
: 1000 hrs
Applied current : Rated current
Recovery
: At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
LHL□□□ : Temperature
Humidity
: 40±2℃
: 90～95%RH
: 1000±24 hrs
Duration
Applied current : Rated current
Recovery
: 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
FL
: Temperature
Humidity
Duration
: 60±3℃
: 90～95%RH
: 500 (＋12, ー0) hrs
Applied current : Rated current
Recovery
: 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
26. Loading at high temperature
LA Type
△L/L : Within ±10%ꢀQ : ±30min
△L/L : Within ±10%
CAL45 Type
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA
: Temperature
Duration
: 85±2℃
: 1000 hrs
Applied current : Rated current
Recovery : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
27. Low temperature life test
LA Type
△L/L : Within ±10%ꢀQ : ±30min
△L/L : Within ±10%
CAL45 Type
LHL□□□
FBA/FBR
Appearance : No abnormality
Inductance change : Within ±10%
Impedance change : Within ±20%
Q change : Within ±30% (LHLP : only △L/L)
FL05□ Type
FL06BT Type
Refer to individual specification
Appearance : No abnormality
【Test Method and Remarks】
LA, CA
: Temperature : ー25±2℃
Duration
: 1000 hrs
: At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
Recovery
LHL□□□ : Temperature : ー40±3℃
Duration
Recovery
: 1000±24 hrs
: 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
FL
: Temperature : ー40±3℃
Duration
: 500 (＋12, ー0) hrs
: 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
Recovery
28. High temperature life test
LA Type
CAL45 Type
LHL□□□
FBA/FBR
Appearance : No abnormality
Inductance change : Within ±10%
Impedance change : Within ±20%
Q change : Within ±30% (LHLP : only △L/L)
FL05□ Type
FL06BT Type
Refer to individual specification
Appearance : No abnormality
【Test Method and Remarks】
LHL□□□ : Temperature : 105±3℃
Duration
Recovery
: 1000±24 hrs
: 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
FL
: Temperature : 85±3℃
Duration
: 500 (＋12, ー0) hrs
: 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
Recovery
＊This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
le0104fi01_reli_e-01
le0104fi01_reli-RP6
■ PRECAUTIONS
CAL Type, LH Type, FB Type, FL Type, LA Type
1. Circuit Design
◆Operating environment
1.The products described in this specification are intended for use in general electronic equipment,(office supply equipment, telecommunications systems,
Precautions
measuring equipment, and household equipment). They are not intended for use in mission-critical equipment or systems requiring special quality and high
reliability (traffic systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems,) where
product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance.
2. PCB Design
◆Design
Precautions
1.Please design insertion pitches of a base in the pitches that fitted a terminal interval.
Technical ◆Design
consider-
ations
1.When Inductors are mounted onto a PC board, hole dimensions on the board should match the lead pitch of the component, if not, it will cause breakage of
the terminals or cracking of terminal roots covered with resin as excess stress travels through the terminal legs.
3. Considerations for automatic placement
◆Adjustment of mounting machine
1.Excessive impact load should not be imposed on the products when mounting onto the PC boards.
Precautions
2.Mounting and soldering conditions should be checked beforehand.
Technical
consider-
ations
◆Adjustment of mounting machine
1. When installing products, care should be taken not to apply distortion stress as it may deform the products.
4. Soldering
◆Wave soldering
1. Please refer to the specifications in the catalog for a wave soldering.
2. Do not immerse the entire Inductors in the flux during the soldering operation.
◆Lead free soldering
1.When using products with lead free soldering, we request to use them after confirming of adhesion, temperature of resistance to soldering heat, soldering etc
sufficiently.
Precautions
Recommended conditions for using a soldering iron:
・Put the soldering iron on the land-pattern.
・Soldering iron's temperature - Below 350℃
・Duration - 3 seconds or less
・The soldering iron should not directly touch the inductor.
◆Reflow soldering
1. As for reflow soldering, please contact our sales staff.
Technical ◆Lead free soldering
consider-
ations
1.If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of
the products.
5. Cleaning
Precautions
◆Cleaning conditions
1. CAL type, LH type, LA Type
Please do not do cleaning by a supersonic wave.
Technical ◆Cleaning conditions
consider-
ations
1. CAL type, LH type, LA Type
If washing by supersonic waves, supersonic waves may deform products.
6. Handling
◆Handling
1. Keep the inductors away from all magnets and magnetic objects.
◆Mechanical considerations
1. Please do not give the inductors any excessive mechanical shocks.
Precautions
2. LH type
If inductors are dropped onto the floor or a hard surface they should not be used.
◆Packing
1. Please do not give the inductors any excessive mechanical shocks.
In loading, please pay attention to handling indication mentioned in a packing box (a loading direction / number of maximum loading / fragile item).
◆Handling
1. There is a case that a characteristic varies with magnetic influence.
◆Mechanical considerations
Technical
consider-
ations
1. There is a case to be damaged by a mechanical shock.
2. LH type
There is a case to be broken by a fall.
◆Packing
1. There is a case that a lead route turns by a fall or an excessive shock.
7. Storage conditions
◆Storage
1.To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should
be controlled.
Recommended conditions
Precautions
・Ambient temperature 0～40℃
・Humidity
Below 70% RH
The ambient temperature must be kept below 30℃. Even under ideal storage conditions, solderability of products electrodes may decrease as time passes.
For this reason, inductors should be used within one year from the time of delivery.
In case of storage over 6 months, solderability shall be checked before actual usage.
Technical ◆Storage
consider-
ations
1.Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of
taping/packaging materials may take place.
＊This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
le0104fi01_reli_e-01
le0104fi01_reli-RP7
COMMON MODE CHOKE COIL (SMD) FOR HIGH-SPEED DIFFERENTIAL SIGNAL
REFLOW
■ FEATURES
■ APPLICATIONS
◦CM01 Series is Wire-wound Structured Type Commom Mode Choke
Coil which provides highly effective noise suppression characteristics
without distorting the wave pattern of High-speed Differential Signal
interface.
◦Radiated noise suppression in the High-speed Diffrential Signal inter-
faces [HDMI, Serial-ATA, IEEE1394, LVDS, and USB2.0] of LCD-TV,
Blu-ray players, and PCs.
◦Countermeasure for degradation of receiver sensitivity caused by
high frequency noise from high-speed differential signal of Cellular
phones, Data Cards and Smartphones.
◦Developed 1210 case-size by utilizing our wire-wound technologies.
This small and wire-wound structured product has little transmission
loss and keeps high common impedance up to GHz range.
◦Common mode noise suppression raised from the power line and au-
dio signal in a small device.
◦CM01S600 : Suitable characteristics for super high speed differential sig-
nal such as USB3.0 and so on. Cutoff frequency is 10GHz.
◦CM01H900 : Suitable characteristics for high speed differential signal
such as HDMI, DVI, Displayport and so on. Cut-off frequency is 8GHz.
◦CM01U900 : Suitable characteristics for differential signal such as
USB2.0, LVDS, LAN and so on. Cut-off frequency is 3GHz. High rated
current of this product makes it possible to replace 2012 size product
for this product.
◦CM01U161 : Suitable characteristics for differential signal such as
USB2.0, LVDS, LAN and so on. Cut-off frequency is 3GHz. High com-
mon impedance of this product works effectively on noise suppression.
■ ORDERING CODE
C M 0 1 H 9 0 0 T
❶
❷
❸
❹
❺
❺Packaging
❹Impedance
❶Type
CM Common mode choke coil
❷External Dimensions (L×W)
01 1.2×1.0mm
❸Product classification code
USB3.0 correspondence
T
Taping
600
900
161
60Ω typical at 100MHz
90Ω typical at 100MHz
160Ω typical at 100MHz
S
H
U
HDMI/Displayport correspondence
USB2.0/LAN correspondence
■ EXTERNAL DIMENSIONS/MINIMUM QUANTITY
●CM01TYPE
1.2±0.2
Minimum Quantity (pcs.)
Embossed tape
3000
Type
CM0［1 2 Lines］type
EQUIVALENT CIRCUIT
There is no directionality.
Unit：mm（inch）
0.30±0.1
0.35±0.1
■ PART NUMBERS
●CM01 TYPE
dielectric
resistance
［MΩ］
Characteristic
impedance
Common Impedance DC resistance Rated current Rated voltage
Cut off frequency
Ordering
EHS
No. of Lines
[Ω] (at 100MHz)
[Ω]
[mA]
［V］(D.C.)
［GHz］
［Ω］
CM01S600T
CM01H900T
CM01U900T
CM01U161T
RoHs
RoHS
RoHs
RoHs
2
2
2
2
60typ.
90typ.
90typ.
43min．
65min.
0.4max．
0.5max.
300max．
280max.
20max．
20max.
100min．
100min.
10.0typ.
8.0typ.
3.0typ.
3.0typ.
90typ.
100typ.
－
65min．
0.3max．
0.6max．
400max．
260max．
20max．
20max．
100min．
100min．
160typ. 120min．
－
＊This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
coil01_e-01
138
■ ELECTRICAL CHARACTERISTICS
Impedance characteristics
■
CM01 S600 Type
CM01 H900 Type
CM01 U900 Type
CM01 U161 Type
1000
100
10
1000
1000
100
10
1000
100
10
Common Impedance
Common Impedance
Common Impedance
Common Impedance
100
10
1
Differential Impedance
Differential Impedance
Differential Impedance
Differential Impedance
1
1
1
10
100
1000
10000
10
100
1000
10000
10
100
1000
10000
10
100
1000
10000
Frequenc〔y MHz〕
Frequenc〔y MHz〕
Frequenc〔y MHz〕
Frequenc〔y MHz〕
Transmission characteristic
■
CM01 S600 Type
0
CM01 H900 Type
CM01 U900 Type
CM01 U161 Type
0
－2
0
－2
0
－2
－2
－4
－4
－4
－4
－6
－6
－6
－6
－8
－8
－8
－8
－10
－10
－10
－10
10
100
1000
10000
10
100
1000
10000
10
100
1000
10000
10
100
1000
10000
Frequenc〔y MHz〕
Frequenc〔y MHz〕
Frequenc〔y MHz〕
Frequenc〔y MHz〕
＊This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
coil01_e-01
139
COMMON MODE CHOKE COILS (FOR DC AND SIGNAL LINES) SMD TYPE
REFLOW
■ FEATURES
■ APPLICATIONS
◦Available in embossed tape and reel.
◦Immunity against undesirable external line radiation fields and broad-
cast waves generated by multifunction telephone sets, PBXs, and
facsimile machines.
◦Highly coupled coil construction ideal for common mode noise at-
tenuation.
◦Preventive measure against DC line noise in electronic equipment.
◦Suppresses radiated emissions from secondary power supplies and
signal lines on AC adapters, battery chargers, and digital equipment.
■ OPERATING TEMP.
◦Excellent for reducing radiated noise in DVC (digital video cameras)
and DSC (digital still cameras)
◦ー25℃～105℃（Including self-generated heat）
◦Offers high speed differential mode noise attenuation in USB and
IEEE1394 connectors in personal computers, printers, scanners and
other computer peripherals.
■ ORDERING CODE
C M 0 4 R C 0 1 T ○
❶
❷
❸
❹
❺
❻
❶Type
❷Dimensions of Core (mm)
❸Shape
Surface mount type
❹Product classification code
01～10
❺Packaging
Taped products
❻Internal code
Standard Products
△＝Blank space
CM
BU
04
3.5
RC
MC
T
△
Common mode
choke coils
05
5.0
■ EXTERNAL DIMENSIONS/MINIMUM QUANTITY
BU05MC〔2 Lines〕type
BU05MC〔3 Lines〕type
CM04RC〔2 Lines〕type
Minimum Quantity (pcs.)
Minimum Quantity (pcs.)
Embossed tape
Minimum Quantity (pcs.)
Embossed tape
Embossed tape
2500
2500
1500
（0.5）
（0.020）
（0.5）
（0.020）
（1.3）
（0.05）
（0.5）
（0.020）
1.5±0.2
2.54±0.25
（0.6）
（0.024）
（0.5）
（0.020）
3.0±0.2
（0.118±0.008）
（0.100±0.010）
（0.059±0.008）
5.0±0.3
5.2±0.2
5.0±0.3
（0.197±0.012）
（0.205±0.008）
（0.196±0.012）
CM04RC〔3 Lines〕type
CM04RC〔3 Lines〕type（Thin）
Minimum Quantity (pcs.)
CM04RC〔4 Lines〕type
Minimum Quantity (pcs.)
Minimum Quantity (pcs.)
Embossed tape
Embossed tape
Embossed tape
2500
1000
1000
（0.5）
（0.020）
（1.3）
（1.3）
（0.051）
（0.051）
（0.5）
（0.020）
（0.5）
（0.020）
2.54±0.25
1.27±0.25
2.54±0.25
（0.5）
（0.020）
（0.100±0.010）
（0.050±0.010）
（0.100±0.010）
9.8±0.2
7.4±0.2
5.3±0.2
（0.354±0.008）
（0.291±0.008）
（0.208±0.008）
The values without tolerance are for reference only.
Unit : mm (inch)
■ PART NUMBERS
●CM04RC Type
EHS (Environmental
Insulation
resistance
[MΩ] (min.)
Impedance
[Ω] (typical)
DC resistance
[Ω] (max.)
Rated current
[A] (max.)
Rated voltage
[V] (D.C.)
Ordering code
Hazardous
Substances
No. of Lines
)
CM04RC01T
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
800 (at 100MHz)
900 (at 20MHz)
500 (at 160MHz)
270 (at 200MHz)
100 (at 200MHz)
1000 (at 100MHz)
1000 (at 200MHz)
800 (at 100MHz)
0.06
0.1
1.5
1.3
2.5
3.0
4.0
0.5
0.5
0.5
CM04RC04T
CM04RC07T
CM04RC09T
CM04RC10T
CM04RC02T
CM04RC08T (THIN)
CM04RC05T
2
0.06
0.03
0.02
0.18
0.2
50
100
3
4
0.2
●BU05MC Type
EHS (Environmental
Hazardous
Insulation
resistance
[MΩ] (min.)
Impedance
[Ω] (typical)
DC resistance
[Ω] (max.)
Rated current
[A] (max.)
Rated voltage
[V] (D.C.)
Ordering code
No. of Lines
Substances
)
BU05MC01T
BU05MC08T
RoHS
2
3
1000 (at 60MHz)
700 (at 60MHz)
0.12
0.11
1
50
100
RoHS
0.5
＊This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
coil02_e-01
140
■ ELECTRICAL CHARACTERISTICS
Impedance -vs- Frequency characteristics
■
（Measured by HP4291A）
Common mode
Normal mode
＊This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
coil02_e-01
141
■ PACKAGING
①Minimum Quantity
Type
⑤Taping dimensions
◦Embossed tape (CM01 type)
Minimum Quantity (pcs.)
Embossed tape
CM01 ［2 Lines］type
CM04RC［2 Lines］type
CM04RC［3 Lines］type
CM04RC［3 Lines］type (Thin)
CM04RC［4 Lines］type
BU05MC［2 Lines］type
BU05MC［3 Lines］type
3000
1500
1000
2500
1000
2500
2500
Unit: mm (inch)
②Tape Material
◦Embossed tape (CM04RC type) 8mm pitch (0.31 inches pitch)
Unit: mm (inch)
◦Embossed tape (CM04RC type) 12mm pitch (0.472 inches pitch)
③Leader and Blank Portion
Unit: mm (inch)
◦Embossed tape (BU05MC type)
Blank portions
(Leader side)
Blank portions
(Chip cavity side)
Type
Leader
200～400
(7.87～15.75)
160～200
(6.30～7.87)
CM01
160 (6.30) or more
CM04RC
BU05MC
150 (5.89)
150 (5.89)
80 (3.14)
80 (3.14)
80 (3.14)
80 (3.14)
Unit : mm (inch)
Unit: mm (inch)
tape thickness
④Reel size
Chip cavity
Insertion
pitch
Type
CM01
Lines
A
B
K
T
2
4.0±0.1
8.0±0.1
12.0±0.1
8.0±0.1
1.16±0.1
5.7±0.1
9.8±0.1
5.7±0.1
1.41±0.1 0.98±0.1
0.3max.
0.4±0.05
2
9.65±0.1
7.7±0.1
9.8±0.1
5.2max
3
5.0max 0.38±0.05
CM04RC
BU05MC
3 (THIN)
3.1max
0.4±0.05
0.3±0.05
4
2
3
12.0±0.1 10.3±0.1 10.3±0.1
5.0max
8.0±0.1 5.35±1.5 5.7±0.2
3.2±0.1
0.4±0.05
Unit : mm (inch)
⑥Top Tape Strength
Type
A
B
C
φ60＋1/－0
(φ2.36＋0.039/－0)
φ180＋0/－3
(φ7.09＋0/－0.118)
10.0±1.5
(0.394±0.059)
CM01
φ100±1
φ330±2
18±1.5
CM04RC
BU05MC
(φ3.94±0.039)
(φ12.99±0.079)
(0.709±0.059)
φ80±1
(φ3.15±0.039)
φ330±2
(φ12.99±0.079)
13.5±1
(0.53±0.039)
◦CM01
The top tape requires a peel-off force of 0.1 to 1.0N in the direction of the arrow
as illutrated above.
Unit : mm (inch)
◦CM04RC, BU05MC
The top tape requires a peel-off force of 0.1 to 0.7N in the direction of the arrow
as illutrated above.
＊This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
coil0102_pack_e-01
coil0102_pack-P1
COMMON MODE CHOKE COILS (FOR DC AND SIGNAL LINES) LEADED TYPE
WAVE
■ FEATURES
■ APPLICATIONS
◦TLF Type :
Countermeasure for noise in the low-frequency (AM) broad-casting
band. Shields against radiated emissions in the broadcasting fre-
quency for multi-functional telephone sets. PBXs, faxes, etc.
◦Highly reliable, compact and lightweight
◦Easily inserted into the PCB
◦CM/BU Type
:
Countermeasure for noise in the high-frequency (MHz) band
■ OPERATING TEMP.
TLF Type
ー25℃～＋105℃
CM Type
ー25℃～＋105℃
（Including self-generated heat）
■ ORDERING CODE
【TLF Type】
T L F △ 9 U B H 3 0 2 W ○ ○
❶
❷
❸
❹
❺
❻
❼
❶Type
TLF Line filter
❷Dimensions of core
❸Shape
U core,
vertically split wound
❹Nominal inductance (μH)
example
❺Inductance tolerance (%)
❻❼Internal code
△△ Standard product
△＝Blank space
＋100
△9
9mm
W
ー10
UB△
△＝Blank space
302
203
3000
U core,
horizontally split wound
20000
UBH
△＝Blank space
【CM-BU Type】
C M 0 5 R A 0 6 ○
❶
❷
❸
❹
❺
❶Type
Common mode choke coile
❷Core dimensions（mm）
❸Shape
RA Double-wire lead
❹Product classification code
01～20
❺Internal code
Standard product
△＝Blank space
CM
BU
05
08
12
4.8
△
8.0
RB Pin type with base
12.0
■ EXTERNAL DIMENSIONS/MINIMUM QUANTITY
TLF9UB Type
TLF9UB H Type
CM□□RA Type / BU08RA Type
Minimum Quantity
(pcs.)
Type
Box
ー
ー
ー
ー
Bulk
500
250
100
200
CM05RA06
CM08RA□□
CM12RA02
BU08RA□□
Type
W (max.)
6.5 (0.256)
CM08,BU08 11.0 (0.433)
CM12 15.5 (0.610)
T (max.)
3.0 (0.118)
Minimum Quantity (pcs.)
Box
Minimum Quantity (pcs.)
Box
CM05
6.0, 7.0 (0.024, 0.276)
7.0 (0.276)
500
500
CM05RB (2Lines Type)
CM08RB (2Lines) Type
CM08RB (4Lines) Type
Minimum Quantity (pcs.)
Minimum Quantity (pcs.)
Minimum Quantity (pcs.)
Box
Bulk
Box
500
Bulk
Box
500
Bulk
1000
ー
ー
ー
Unit : mm (inch)
＊This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
coil03_e-01
142
■ PART NUMBERS
EHS (Environmental
Hazardous
Insulation
resistance
[MΩ] (min.)
Inductance
[μH] [＋ー11000 %]
DC resistance
[Ω] (max.)
Rated current
[A] (max.)
Rated voltage
[V] D.C.
Impedance [KΩ]
(Reference values)
Ordering code
No. of lines
Substances
)
TLF9UBH 302W
TLF9UB 302W
TLF9UBH 802W
TLF9UB 802W
TLF9UBH 203W
TLF9UB 203W
RoHS
3000
8000
1.5
3.0
6.5
0.4
0.3
≧20 (at 1MHz)
RoHS
RoHS
2
50
100
≧40 (at 700kHz)
≧150 (at 500kHz)
RoHS
RoHS
20000
0.18
RoHS
EHS (Environmental
Hazardous
Insulation
resistance
[MΩ] (min.)
Inductance
[μH] [at 1kHz]
Impedance
[Ω] (typical)
DC resistance
[Ω] (max.)
Rated current
[A] (max.)
Rated voltage
[V] D.C.
Ordering code
No.of lines
Substances
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
)
CM05RA
BU08RA
06
11
16
17
20
02
01
03
01
02
04
05
03
0.7 min.
0.7～1.3
1.19～2.21
15.0 min.
6.0 min.
700 (at 200MHz)
1000 (at 250MHz)
1200 (at 200MHz)
2000 (at 80MHz)
500 (at 200MHz)
2000 (at 80MHz)
700 (at 70MHz)
1400 (at 100MHz)
2500 (at 30MHz)
2000 (at 50MHz)
2000 (at 70MHz)
450 (at 100MHz)
1000 (at 50MHz)
0.050
0.013
0.011
0.040
0.020
0.040
0.050
0.060
0.040
0.040
0.040
0.020
0.050
1.5
4.0
3.0
2.4
5.5
3.0
2.0
1.5
2.0
2.4
3.0
4.0
2.0
CM08RA
CM12RA
CM05RB
10.0 min.
7.0 min.
2
4
50
100
15.0 min.
40.0 min.
15.0 min.
110.0 min.
6.0 min.
CM08RB
15.0 min.
■ ELECTRICAL CHARACTERISTICS
Measuring conditions
Equipment
: HP4291A Vosc: 0.5V (CM/BU type)
HP4192A Vosc: 0.35V (TLF type)
Measuring circuit :
To impedance analyzer
＊This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
coil03_e-01
143
COMMON MODE CHOKE COILS (FOR AC LINES) LEADED TYPE
WAVE
■ FEATURES
■ APPLICATIONS
◦TLF 9UA (H) Type : Small-sized configuration
◦TLF14CB (H) Type : Ordinary configuration
◦As a preventive measure against noise terminal voltage or power
supply noise in TV or VTR units, SW power supplies, NC machines,
computer systems, peripheral units, measuring instruments, and con-
trollers.
◦TLF 9UA (H) Type : low-current applications
◦TLF14CB (H) Type : equipment with several tens of watts of input power
■ OPERATING TEMP.
TLF9U Type
ー25℃～＋105℃
TLF14CB Type
ー25℃～＋105℃
（Including self-generated heat）
■ ORDERING CODE
T L F △ 9 U A H 1 0 2 W 0 R 8 ○ ○
❶
❷
❸
❹
❺
❻
❼
❽
❶Type
TLF Line filter
❷Core dimensions（mm）
❹Nominal Inductance (μH)
example
❺Inductance tolerance (%)
❻Rated current (A)
❽Internal code
Standard Product
△＝Blank space
△9
9
R54
0.54
△
△
Nominal Values or higher
102
103
1000
14
14
0R8
0.8
＋100
ー10
W
△＝Blank space
10000
※R=decimal point
△＝Blank space
❸Shape
❼Product classification code
UA△
UAH
CB△
CBH
U core, vertical type
△
Standard
△＝Blank space
U core, horizontal type
Square type core vertically split wound
Square type core horizontally split wound
△＝Blank space
■ EXTERNAL DIMENSIONS/MINIMUM QUANTITY
TLF14CB Type
TLF14CBH Type
Minimum Quantity (pcs.)
Box
Type
TLF9UA□
TLF14CB□
500
500
TLF9UA Type
TLF9UA H Type
Unit : mm (inch)
＊This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
coil04_e-01
144
■ PART NUMBERS
Withstanding
voltage
［V］（min.）
[1 minute]
Applicable
frequency
[MHz]
EHS (Environmental
Hazardous
Inductance
[mH]
Inductance
Tolerance
DC resistance Rated current Rated voltage
Type
Ordering code
[Ω] (max.)
[A] (max.)
[V]（max.）
Substances
)
Reference Value
TLF9UA
TLF9UA
TLF9UA
TLF9UA
TLF9UA
TLF9UA
102W0R8
202WR54
302WR42
502WR32
802WR25
103WR23
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
1
2
＋100％/ー10％
＋100％/ー10％
＋100％/ー10％
＋100％/ー10％
＋100％/ー10％
＋100％/ー10％
＋100％/ー10％
＋100％/ー10％
＋100％/ー10％
＋100％/ー10％
＋100％/ー10％
＋100％/ー10％
min
0.5
1.0
0.80
0.54
0.42
0.32
0.25
0.23
0.80
0.54
0.42
0.32
0.25
0.23
1.5
3
1.5
TLF9UA
5
2.5
4.0
4.5
0.5
1.0
8
10
1
TLF9UA H102W0R8
TLF9UA H202WR54
TLF9UA H302WR42
TLF9UA H502WR32
TLF9UA H802WR25
TLF9UA H103WR23
TLF14CB 102 1R5
TLF14CB 222 1R2
TLF14CB 332 1R0
TLF14CB 472 1R0
TLF14CB 562 0R8
TLF14CB 682 0R8
TLF14CB 103 0R7
TLF14CB 223 0R4
TLF14CB 333 0R3
TLF14CB 473 0R2
TLF14CB 563 0R2
TLF14CB 683 0R2
TLF14CBH102 1R5
TLF14CBH222 1R2
TLF14CBH332 1R0
TLF14CBH472 1R0
TLF14CBH562 0R8
TLF14CBH682 0R8
TLF14CBH103 0R7
TLF14CBH223 0R4
TLF14CBH333 0R3
TLF14CBH473 0R2
TLF14CBH563 0R2
TLF14CBH683 0R2
2
3
1.5
TLF9UAH
5
2.5
4.0
4.5
0.1
8
10
1.0
2.2
3.3
4.7
5.6
6.8
10
22
33
47
56
68
1.0
2.2
3.3
4.7
5.6
6.8
10
22
33
47
56
68
min
0.18
0.32
0.38
0.42
0.6
0.85
1.7
1.2
min
1.0
min
1.0
min
0.8
min
0.8
TLF14CB
AC250
AC2000
0.1～10
min
0.7
min
0.4
min
2.7
0.3
min
3.6
5
0.2
min
0.2
min
6.5
0.1
0.2
min
1.5
min
0.18
0.32
0.38
0.42
0.6
0.85
1.7
1.2
min
1.0
min
1.0
min
0.8
min
0.8
TLF14CBH
min
0.7
min
0.4
min
2.7
0.3
min
3.6
5
0.2
min
0.2
min
6.5
0.2
■ ELECTRICAL CHARACTERISTICS
Impedance-Frequency characteristic
■
TLF9UA/TLF9UAH Type
TLF14CB/TLF14CBH Type
Test conditions
Equipment : HP-4192A Vosc-0.35V
Test circuit :
To impedance analyzer
＊This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
coil04_e-01
145
■ PACKAGING
Minimum Quantity
◦CM/BU Type
Minimum Quantity (pcs.)
Type
Box
Bulk
500
—
CM05RA06
—
1000
CM05RB□□
CM08RA□□
CM08RB□□
CM12RA02
—
500
—
250
—
100
200
BU08RA□□
—
◦TLF Type
Minimum Quantity (pcs.)
Type
Box
500
500
500
TLF9UA□
TLF9UB□
TLF14CB□
＊This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
coil0304_pack_e-01
coil0304_pack-P1
BALUN TRANSFORMERS
WAVE
REFLOW
M B：
M C：
■ FEATURES
■ APPLICATIONS
◦High stability due to pair wire windings
◦Impedance transformers
◦Distribution transformers
◦MC type : pins are molded into the base to create a singular structure
◦This item can be custom designed to meet customer requirements
■ OPERATING TEMP.
◦ー25℃～105℃（Including self-generated heat）
■ ORDERING CODE
B U 0 5 M B 0 1 △ ○
❶
❷
❸
❹
❺
❻
❶Type
BU Balun transformer
❷Length of component [mm]
❸Shape
MB pin type
MC Surface-mount type
❺Packaging
Tape & Reel
❻Internal code
Standard product
△＝Blank space
05
5.0、5.3
T
△
06
6.0
△
Bulk (Only pin type)
△＝Blank space
❹Product classification code
example
01
■ EXTERNAL DIMENSIONS/MINIMUM QUANTITY
Pin type
MB (BU05MB, BU06MB)
Surface-mount type
MC (BU05MC)
Type
B
B
Fig.
D
D
Recommended Land Patterns
Minimum Quantity (pcs.)
Type
A
B
C
D
E
【BU05MC】
Box
Taping
0.5
0.5
5.5 max.
5.5 max.
6.0 max.
1.75±0.2
3.5
（0.138）
3.5～5.0
BU05MB
BU06MB
BU05MC
200
ー
（0.217 max.） （0.217 max.） （0.236 max.） （0.069±0.008）
8 max. 8 max. 8 max. 2.25±0.2 pitch
（0.315 max.） （0.315 max.） （0.315 max.） （0.089±0.008）（0.138±0.197）
1.6
150
ー
5.3±0.5
5.0±0.3
2.7±0.2
1.5±0.2 pitch
1.6
ー
ー
2500
（0.209±0.020）（0.197±0.012）（0.106±0.008）（0.059±0.008）
Unit : mm (inch)
1
1
1
Unit : mm (inch)
■ ELECTRICAL CHARACTERISTICS
The following chart shows typical ranges for operating characteristics.
Please specify the following when ordering.
① loss
② standing wave ratio (VSWR)
③ operating frequency
④ specified test circuit
＊This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
trans01_e-01
146
■ PACKAGING
①Minimum Quantity
Type
⑥Top Tape Strength
The top tape requires a peel-off force of 0.1 to 0.7N in the direction of the arrow
as illustrated below.
Minimum Quantity (pcs.)
Taping
Box
ー
200
BU05MC
BU05MB
BU06MB
2500
ー
ー
150
②Tape material
③Taping dimensions
◦Embossed tape 12mm wide (0.472 inches wide)
3.2
±0.1
2±0.1
8
±
0.1
0.004）
4±0.1
（0.157 0.004）
（
1.5+0.1
）
0
（0.126±0.004）
（0.079±0.004）
-
（0.315
±
（
0.059+0.004
）
1.75±0.1
（0.069±0.004）
-0
0.4±0.05
（0.016±0.002）
±
5.2±0.1
（0.209±0.004）
Unit : mm (inch)
④Leader and Blank portion
⑤Reel size
Label
13.5±1
（0.53±0.039）
Unit : mm (inch)
＊This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
trans01_pack_e-01
trans01_pack-P1
■ RELIABILITY DATA
1. Operating Temperature Range
CM01
ー40℃～＋105℃
ー25℃～＋105℃
CM04RC
BU05MC
【Test Method and Remarks】
Including self-generated heat
2. Storage Temperature Range
CM01
CM04RC
BU05MC
ー40℃～＋85℃
【Test Method and Remarks】
ー5 to ＋40℃ in taped packaging
3. Rated current
CM01
CM04RC
Within the specified tolerance.
BU05MC
【Test Method and Remarks】
The maximum DC value having temperature increase within specified temperature,as detailed in individual specification.
4. Impedance
CM01
CM04RC
Within the specified tolerance.
BU05MC
【Test Method and Remarks】
Measuring equipment : HP 4291A or its equivalent
Measuring frequency : Specified frequency
5. DC Resisitance
CM01
CM04RC
BU05MC
Within the specified tolerance.
【Test Method and Remarks】
SMD transformer・Commom mode choke coil :
Measuring equipment : DC ohm meter
6. Resistance to flexure of substrate
CM01
Within the specified tolerance.
CM04RC
BU05MC
Refer to individual specification.
【Test Method and Remarks】
According to JIS C 0051
CM01
2mm
CM04RC・BU05MC
Warp
3mm
Pressing speed
Duration
0.5mm/sec.
5±1sec.
7. Dielectric resistance : between wires
CM01
CM04RC
BU05MC
100MΩ min.
【Test Method and Remarks】
Applied voltage : Rated voltage
Duration
: 60 sec.
8. Rated voltage
CM01
CM04RC
Within the specification.
BU05MC
9. Withstanding voltage : between wires
CM01
CM04RC
BU05MC
No abnormality.
【Test Method and Remarks】
Applied voltage : Regulation voltage
Duration
: 60 sec.
10. Resistance to vibration
CM01
No abnormality observed in appearance
Refer to individual specification.
CM04RC
BU05MC
【Test Method and Remarks】
According to JIS C 0040
Directions
: 2 hrs each in X, Y, and Z directions. Total : 6 hrs
Frequency range : 10 to 55 to 10 Hz (1 min.)
Amplitude
: 1.5mm (Shall not exceed acceleration 196m/s2)
Mounting method : soldering onto printed board
Recovery
: At least 2 hrs of recovery under the standard condition after the test,followed by the measurement within 48 hrs.
＊This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
co0102tr01_reli_e-01
co0102tr01_reli-RP1
■ RELIABILITY DATA
11. Solderability
CM01
At least 90% of terminal electrode is covered by new solder.
At least 75% of terminal electrode is covered by new solder.
CM04RC
BU05MC
【Test Method and Remarks】
CM01
245±5℃
3±1sec.
－
CM04RC・BU05MC
235±5℃
2±0.5sec.
Up to 0.5mm from terminal root
Solder temperature
Duration
Immersion depth
12. Resistance to solder Heat
CM01
Within the specified tolerance.
Refer to individual specification.
CM04RC
BU05MC
【Test Method and Remarks】
CM01
CM04RC・BU05MC
Preheating
Peak
: 150 to 180℃ 1 to 2min
: 255±5℃ 5sec.
Preheating
Peak
: 100 to 150℃ 1 to 2min
: 230 to 240℃ within 5sec.
More than 200℃ within 40sec.
Reflow soldering
Manual soldering
230±5℃ 30～40sec.
Number of reflow : Within 2 times
Number of reflow: Within 2 times
Solder temperature : 350±5℃
Duration: 3±1sec.
Recovery : 1 to 2hrs of recovery under the standard
condition after the test.
－
13. Thermal shock
CM01
Within the specified tolerance.
Refer to individual specification.
CM04RC
BU05MC
【Test Method and Remarks】
Accoding to JIS C 0025
Conditions of 1 cycle
Temperature (℃)
Time (min)
CM04RC・BU05MC
30±3
3
30±3
3
Step
CM01
CM04RC・BU05MC
ー25±3℃
Room Temp.
CM01
1
2
3
4
ー40±3℃
Room Temp.
85±2℃
85±3℃
Room Temp.
Room Temp.
Number of cycle : CM01
: 100 cycle
CM04RC・BU05MC : 10 cycle
Recovery : Recovery under the standard condition after removal from test chamber.
CM01 : Measuring it more than two hours and less than 48 hours.
CM04RC・BU05MC : Leave during 1～2 hour.
14. Loading under damp heat
CM01
Within the specified tolerance.
Refer to individual specification.
CM04RC
BU05MC
【Test Method and Remarks】
CM01
60±2℃
CM04RC・BU05MC
40±3℃
90～95％RH
Temperature
Humidity
Applied current
Duration
Rated current
1000±24hrs
Recovery : Recovery under the standard condition after removal from test chamber.
CM01 : Measuring it more than two hours and less than 48 hours.
CM04RC・BU05MC : Leave during 1～2 hour.
15. High temperature life test
CM01
ー
CM04RC
Refer to individual specification.
BU05MC
【Test Method and Remarks】
CM04RC・BU05MC
Temperature
Duration
85±3℃
1000±24hrs
Recovery : Recovery under the standard condition after removal from test chamber.
CM01 : Measuring it more than two hours and less than 48 hours.
CM04RC・BU05MC : Leave during 1～2 hour.
16. Low Temperature life Test
CM01
Within the specified tolerance.
Refer to individual specification.
CM04RC
BU05MC
【Test Method and Remarks】
CM01
－40±2℃
CM04RC・BU05MC
－40±3℃
Temperature
Applied current
1000±24hrs
Recovery : Recovery under the standard condition after removal from test chamber.
CM01 : Measuring it more than two hours and less than 48 hours.
CM04RC・BU05MC : Leave during 1～2 hour.
＊This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
co0102tr01_reli_e-01
co0102tr01_reli-RP2
■ RELIABILITY DATA
17. Loading at high temperature life test
CM01
Within the specified tolerance.
CM04RC
ー
BU05MC
【Test Method and Remarks】
CM01
Temperature
Applied current
Duration
105±2℃
Rated current
1000±24hrs
Recovery : Recovery under the standard condition after removal from test chamber.
CM01 : Measuring it more than two hours and less than 48 hours.
CM04RC・BU05MC : Leave during 1～2 hour.
Note on standard condition :
"standard condition" referred to herein is defined as follows:
5 to 35℃ of temperature, 45 to 85% relative humidity and 86 to 106kPa of air pressure.
When there are questions concerning measurement results:
In order to provide correlation data, the test shall be conducted under condition of 20±2℃ of temperature, 45 to 85% relative humidity and 86 to 106kPa of air pressure.
Unless otherwise specified, all the tests are conducted under the "standard condition."
＊This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
co0102tr01_reli_e-01
co0102tr01_reli-RP3
■ PRECAUTIONS
CM04RC, BU05MC, CM01
1. Circuit Design
◆Operating environment
1.The products described in this specification are intended for use in general electronic equipment, (office supply equipment, telecommunications systems,
measuring equipment, and household equipment). They are not intended for use in mission-critical equipment or systems requiring special quality and high
reliability (traffic systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems,) where
product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance.
Precautions
2. PCB Design
◆Land pattern design
Precautions
1.Please contact any of our offices for a land pattern, and refer to a recommended land pattern of specifications.
◆Land pattern design
【CM04RC】
【BU05MC】
0.5 0.5
【CM01】
Surface Mounting
・Mounting and soldering conditions should be checked
beforehand.
・Applicable soldering process to this products is reflow
soldering only.
・Recommended Land Patterns
0.45
1.6
6.7
0.65 1.55
0.45
1.4
3.2
1.4
Technical
consider-
ations
0.3
0.4
0.4
1.6
1.1
1
1
1
1.8 0.74 1.8
Unit: mm
3. Considerations for automatic placement
◆Adjustment of mounting machine
1.Excessive impact load should not be imposed on the products when mounting onto the PC boards.
2.Mounting and soldering conditions should be checked beforehand.
Precautions
Technical
consider-
ations
◆Adjustment of mounting machine
1. When installing products, care should be taken not to apply distortion stress as it may deform the products.
4. Soldering
◆Reflow soldering
1. Please contact any of our offices for a reflow soldering, and refer to the recommended condition specified.
2. This product is reflow soldering only.
3. Please do not add any stress to a product until it returns in normal temperature after reflow soldering.
◆Lead free soldering
1.When using products with lead free soldering, we request to use them after confirming of adhesion, temperature of resistance to soldering heat, soldering etc sufficiently.
◆Recommended conditions for using a soldering iron
【CM04RC, BU05MC】
Precautions
・Put the soldering iron on the land-pattern.
・Soldering iron's temperature - Below 350℃
・Duration - 3 seconds or less
・The soldering iron should not directly touch the inductor.
【CM01】
・Please do not conduct an adjustment with a soldering iron because the wire would be broken due to its thinness.
◆Reflow soldering
Technical
consider-
ations
1.If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of the
products.
5. Cleaning
Precautions
◆Cleaning conditions
1. Please contact any of our offices for a cleaning.
6. Handling
Precautions
◆Handling
1. Keep the product away from all magnets and magnetic objects.
◆Breakaway PC boards (splitting along perforations)
1. When splitting the PC board after mounting product, care should be taken not to give any stresses of deflection or twisting to the board.
2. Board separation should not be done manually, but by using the appropriate devices.
◆Mechanical considerations
1. Please do not give the product any excessive mechanical shocks.
2. Please do not add any shock and power to a product in transportation.
◆Pick-up pressure
1. Please do not push to add any pressure to a winding part.
Please do not give any shock and push into a ferrite core exposure part.
◆Packing
1. Please avoid accumulation of a packing box as much as possible.
◆Handling
1. There is a case that a characteristic varies with magnetic influence.
◆Breakaway PC boards (splitting along perforations)
1. Planning pattern configurations and the position of products should be carefully performed to minimize stress.
Technical ◆Mechanical considerations
consider-
ations
1. There is a case to be damaged by a mechanical shock.
2. There is a case to be broken by the handling in transportation.
◆Pick-up pressure
1. Damage and a characteristic can vary with an excessive shock or stress.
◆Packing
1. There is a case that transformation and a product of tape are damaged by accumulation of a packing box.
7. Storage conditions
◆Storage
1.To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should be controlled.
・Recommended conditions
Ambient temperature: 0～40℃
Precautions
Humidity
: Below 70% RH
The ambient temperature must be kept below 30℃. Even under ideal storage conditions, solderability of products electrodes may decrease as time passes.
For this reason, product should be used within one year from the time of delivery.
In case of storage over 6 months, solderability shall be checked before actual usage.
Technical ◆Storage
consider-
ations
1.Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration
oftaping/packaging materials may take place.
＊This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
co0102tr01_reli_e-01
co0102tr01_reli-RP4
■ RELIABILITY DATA
1. Operating Temperature Range
CM-RA/BU-RA Type
ー25～＋105℃
CM-RB Type
TLF9U, TLF14CB
TLF9U : ー25～＋105℃, TLF14CB : ー25～＋105℃
【Test method and remarks】
Including temperature rise due to self-generated heat.
2. Storage temperature range
CM-RA/BU-RA Type
CM-RB Type
ー40～＋85℃
TLF9U, TLF14CB
3. Rated current
CM-RA/BU-RA Type
CM-RB Type
Within the specified range
TLF9U, TLF14CB
【Test method and remarks】
CM : The maximum DC value having temperature increase within specified temperature, as detailed in individual specification.
TLF9UA、14CB : The maximum AC value having temperature increase within 45℃ by the application of AC current.
TLF9UB : The maximum DC value having temperature increase within 45℃ by the application of DC current.
4. Inductance
CM-RA/BU-RA Type
CM-RB Type
Within the specified tolerance
TLF9U, TLF14CB
【Test method and remarks】
CM :
Measuring equipment : 4263A (HP) or its equivalent
Measuring frequency : 1kHz
TLF9UA :
Measuring equipment : Impedance analyzer (HP4192A) or its equivalent
Measuring frequency : 1kHz
Measuring voltage
: 0.35Vosc
TLF14CB :
Measuring equipment : LCR meter 4284A or its equivalent
Measuring frequency : 1kHz
Measuring voltage
: 1.0V
5. DC resistance
CM-RA/BU-RA Type
CM-RB Type
Within the specified tolerance
TLF9U, TLF14CB
【Test method and remarks】
CM・TLF : Measuring equipment : DC ohmmeter
6. Terminal strength tensile force
CM-RA/BU-RA Type
CM-RB Type
No abnormality
TLF9U, TLF14CB
【Test method and remarks】
CM : Fix the component in the direction to draw terminal and gradually apply tensile force as detailed in indiviual specifications.
TLF9U : Apply the stated tensile force gradually in the direction to draw terminal.
Nominal wire diameter tensile
TLF14CB : Apply the stated tensile force gradually in the direction to draw terminal.
Nominal wire diameter tensile
force [N]
5
duration [s]
force [N]
10
duration [s]
φd [mm]
φd [mm]
φ0.6
30±5
φ0.8
30±5
7. Temperature rise
CM-RA/BU-RA Type
CM-RB Type
Refer to individual specification
TLF9U, TLF14CB
45℃ max.
【Test method and remarks】
TLF : Resistance substitution method
Applied current : Rated current
Duration : 1 hour
8. Insulation resistance between wires
CM-RA/BU-RA Type
CM-RB Type
100MΩ min.
TLF9U, TLF14CB
【Test method and remarks】
CM・TLF: Applied voltage : Rated voltage (CM-RA/BU-RA, CM-RB）
: 500VDC (TLF9UA, 14CB)
: 250VDC (TLF9UB)
Duration : 60sec.
＊This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
co0304_reli_e-01
co0304_reli-RP1
■ RELIABILITY DATA
9. Insulation resistance between wire and core
CM-RA/BU-RA Type
CM-RB Type
TLF9U, TLF14CB
100MΩ min.
【Test method and remarks】
TLF : Applied voltage : 500VDC (TLF9UA, 14CB)
: 250VDC (TLF9UB)
Duration : 60 sec.
10. Withstanding : between wires
CM-RA/BU-RA Type
CM-RB Type
No abnormality
TLF9U, TLF14CB
【Test method and remarks】
CM・TLF : Applied voltage : 250VDC (CM-RA/BU-RA, CM-RB）
: 2000VAC (TLF9UA, 14CB）
: 500VDC (TLF9UB)
Duration : 60sec.
11. Withstanding : between wires and core
CM-RA/BU-RA Type
CM-RB Type
TLF9U, TLF14CB
No abnormality
【Test method and remarks】
TLF : Applied voltage : 2000VAC (TLF9UA, 14CB)
: 500VDC (TLF9UB)
Duration
: 60sec.
12. Rated voltage
CM-RA/BU-RA Type
CM-RB Type
Within the specified range
TLF9U, TLF14CB
【Test method and remarks】
TLF9UA, 14CB
TLF9UB
: 250VAC
: 50VDC
13. Resistance to vibration
CM-RA/BU-RA Type
CM-RB Type
Appearance : No abnormality
Inductance change : Within ±15%
TLF9U, TLF14CB
TLF9U : Inductance change : Within ±5％
TLF14CB : Within the specified range
【Test method and remarks】
CM・TLF : According to JIS C 0040
Direction
: 2hrs each in X, Y and Z direction Total : 6hrs
Frequency range : 10 to 55 to 10Hz (1 min.)
Amplitude
: 1.5mm (shall not exceed acceleration 196m/s2)
Mounting method : soldering onto PC board
Recovery
: 2 to 24 hrs of recovery under the standard condition after the test. (CM-RB)
: At least 1hr of recovery under the standard condition after the removal from test chamber, followed by the measurement within 2hrs. (TLF9U, 14CB)
14. Solderability
CM-RA/BU-RA Type
CM-RB Type
At least 75% of terminal electrode is covered by new solder.
Solder shall be uniformly adhered onto immersed surfaces.
TLF9U, TLF14CB
【Test method and remarks】
CM :
Solder temperature : 235±5℃
Duration
: 2±0.5sec.
Immersion depth
: According to detailed specification.
TLF :
Solder temperature : 230±5℃
Duration
: 2±0.5sec. (9U)
: 3±0.5sec. (14CB)
Immersion depth
: Up to 1.0 to 1.5mm from PBC mounted level.
15. Resistance to soldering heat
CM-RA/BU-RA Type
CM-RB Type
Appearance : No abnormality
Inductance change : Refer to individual specification
TLF14CB : Within the specified range
TLF9U, TLF14CB
TLF9UA : Inductance change : Within ±5%
【Test method and remarks】
CM :
Solder temperature : 260±5℃
Duration
: 5±0.5sec.
Immersion depth : Up to 2～2.5mm from terminal root.
Recovery
: 1 to 2 hrs of recovery under the standard condition after the test.
TLF :
Solder temperature : 260±5℃
Duration
: 10±1sec. (9U, 14CB)
Immersion depth : Up to 1.0 to 1.5mm from PBC mounted level.
Recovery
: At least 1hr of recovery under the standard condition after the removal from test chamber, followed by the measurement within 2hrs.
＊This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
co0304_reli_e-01
co0304_reli-RP2
■ RELIABILITY DATA
16. Thermnal shock
CM-RA/BU-RA Type
CM-RB Type
Appearance : No abnormality
TLF9UA
Inductance change : Refer to individual specification
:
Inductance change : Within ±15%
TLF9U, TLF14CB
TLF14CB : Withstanding voltage : No abnormality
Insulation resistance : No abnormality
【Test method and remarks】
CM, TLF :
According to JIS C 0025
Conditions for 1 cycle
Step
Temperature〔℃〕
ー25±3
Room Temperature
Durration〔min〕
30±3
1
2
3
4
Within 3
＋85±2
Room Temperature
30±3
Within 3
Number of cycles : 10
Recovery
: At least 1hr of recovery under the standard condition after the removal from test chamber, followed by the measurement within 2 hrs.
17. Damp heat
CM-RA/BU-RA Type
CM-RB Type
TLF9UA
: Inductance change : Within ±15%
TLF9U, TLF14CB
TLF14CB : Withstanding voltage : No abnormality
Insulation resistance : No abnormality
【Test method and remarks】
TLF :
Temperature : 60±2℃
40±2℃ (※TLF14CB)
Humidity
Duration
Recovery
: 90～95％RH
: 500 hrs
: At least 1hr of recovery under the standard removal from test chamber followed by the measurement within 2 hrs.
18. Loading under damp heat
CM-RA/BU-RA Type
CM-RB Type
Appearance : No abnormality
Inductance change : Refer to individual specification
Insulation resistance : No abnormality
TLF9U, TLF14CB
Withstanding voltage : No abnormality
【Test method and remarks】
CM :
Temperature
Humidity
Duration
: 40±2℃
: 90～95%RH
: 500 (＋12, ー0) hrs
Applied current : Rated current
Recovery
: 1 to 2hrs of recovery under the standard condition after the removal from test chamber.
TLF :
Temperature
: 60±2℃
40±2℃ (※TLF14CB)
Humidity
Duration
: 90～95%RH
: 100 hrs
500 hrs Apply rated current across windings (※TLF14CB)
Applied voltage : Apply the following specified voltage between windings.
TLF9UA
TLF9UB
250VAC
50VDC
Recovery
: At least 1hr of recovery under the standard removal from test chamber followed by the measurement within 2 hrs.
19. Loading at high temperature
CM-RA/BU-RA Type
CM-RB Type
TLF9U, TLF14CB
Withstanding voltage : No abnormality
Insulation resistance : No abnormality
【Test method and remarks】
TLF :
Temperature
Duration
: 85±2℃
: 100 hrs
500 hrs Apply rated current across windings (※TLF14CB)
Applied voltage : Apply the following specified voltage between windings.
TLF9UA
TLF9UB
250VAC
50VDC
Recovery
: At least 1hr of recovery under the standard removal from test chamber followed by the measurement within 2 hrs.
20. Low temperature life test
CM-RA/BU-RA Type
CM-RB Type
Appearance : No abnormality
Inductance change : Refer to individual specification
Insulation resistance : No abnormality
TLF9UA
:
Inductance change : Within ±15%
TLF9U, TLF14CB
TLF14CB: Withstanding voltage : No abnormality
【Test method and remarks】
CM :
Temperature : ー40±3℃
Duration
: 500 (＋12, ー0) hrs
Recovery
: 1 to 2hrs of recovery under the standard condition after the removal from test chamber. (CM-RA)
: 1 to 2hrs of recovery under the standard condition after the removal from test chamber. (CM-RB)
TLF :
Temperature : ー25±2℃
: ー40±2℃ (※TLF14CB)
: 500 hrs
: At least 1hr of recovery under the standard removal from test chamber followed by the measurement within 2 hrs.
Duration
Recovery
＊This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
co0304_reli_e-01
co0304_reli-RP3
■ RELIABILITY DATA
21. High Temperature life test
CM-RA/BU-RA Type
CM-RB Type
Appearance : No abnormality
Inductance change : Refer to individual specification
Insulation resistance : No abnormality
TLF9U
:
Inductance change
:
Within ±15%
TLF9U, TLF14CB
TLF14CB :
Withstanding voltage : No abnormality
【Test method and remarks】
CM :
Temperature : 85±2℃
Duration
: 500 (＋12, ー0) hrs
Recovery
: 1 to 2hrs of recovery under the standard condition after the removal from test chamber. (CM-RA)
: 1 to 2hrs of recovery under the standard condition after the removal from test chamber. (CM-RB)
TLF :
Temperature : 85±2℃
: 105±3℃ (※TLF14CB)
: 500 hrs
: At least 1hr of recovery under the standard removal from test chamber followed by the measurement within 2 hrs.
Duration
Recovery
＊This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
co0304_reli_e-01
co0304_reli-RP4
■ PRECAUTIONS
CM-RA Type, CM-RB Type, TLF Type
1. Circuit Design
◆Operating environment
1.The products described in this specification are intended for use in general electronic equipment, (office supply equipment, telecommunications systems,
Precautions
measuring equipment, and household equipment). They are not intended for use in mission-critical equipment or systems requiring special quality and high
reliability (traffic systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems) where
product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance.
2. PCB Design
◆Design
Precautions
1.Please design insertion pitches of a base in the pitches that fitted a terminal interval.
Technical ◆Design
consider-
ations
1.When Inductors are mounted onto a PC board, hole dimensions on the board should match the lead pitch of the component, if not, it will cause breakage of
the terminals or cracking of terminal roots covered with resin as excess stress travels through the terminal legs.
3. Soldering
Precautions
◆Wave soldering
1. Please refer to the specifications in the catalog for a wave soldering.
2. Do not immerse the entire Inductors in the flux during the soldering operation.
◆Lead free soldering
1.When using products with lead free soldering, we request to use them after confirming of adhesion, temperature of resistance to soldering heat, etc.
sufficiently.
◆Recommended conditions for using a soldering iron
・Put the soldering iron on the land-pattern.
・Soldering iron's temperature - Below 350℃
・Duration - 3 seconds or less
・The soldering iron should not directly touch the product.
Technical ◆Lead free soldering
consider-
ations
1.If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of
the products.
4. Cleaning
Precautions
◆Cleaning conditions
1. TLF type
Please contact any of our offices for about a cleaning.
5. Handling
◆Handling
1. Keep the product away from all magnets and magnetic objects.
◆Mechanical considerations
1. Please do not give the product any excessive mechanical shocks.
Precautions
2. TLF type
Please do not add any shock or and power to a product in transportation.
◆Packing
1. Please do not give the product any excessive mechanical shocks.
In loading, please pay attention to handling indication mentioned in a packing box (a loading direction / number of maximum loading / fragile item).
◆Handling
1. There is a case that a characteristic varies with magnetic influence.
◆Mechanical considerations
Technical
consider-
ations
1. There is a case to be damaged by a mechanical shock.
2. TLF type
There is a case to be broken by a fall.
◆Packing
1. There is a case that a lead route turns at by a fall or an excessive shock.
6. Storage conditions
◆Storage
1.To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should
be controlled.
・Recommended conditions
Ambient temperature: 0～40℃
Precautions
Humidity
: Below 70% RH
The ambient temperature must be kept below 30℃. Even under ideal storage conditions, solderability of products electrodes may decrease as time passes.
For this reason, product should be used within one year from the time of delivery.
In case of storage over 6 months, solderability shall be checked before actual usage.
Technical ◆Storage
consider-
ations
1.Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of
taping/packaging materials may take place.
＊This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
co0304_reli_e-01
co0304_reli-RP5
相关型号：
©2020 ICPDF网 联系我们和版权申明